Skip to main content

5 Common Electrical Problems every home can have


Whenever you have an electrical problem, it’s important that you do not attempt to fix it yourself as electricity is very dangerous and all repairs should be done by a qualified electrician on The Gold Coast. By law, only licensed and qualified electricians are allowed to deal with electrical problems.
The top five most common electrical problems every home can have are:

1.      Electrical Outlets in the Bathroom or Kitchen

All electrical outlets in the bathroom, kitchen, laundry any other areas where there is likely to be moisture should be fitted with GFCI or Ground Fault Circuit Interrupt outlets. These are outlets specially designed to detect any changes in the current flow and shut off the current when they detect any variation in the flow, usually because of a short to water or moisture.

If one of these outlet’s stops working, it’s because they have sensed a problem and shut off. This could be because the appliance they are connected to is faulty or has become wet

2.     Circuit Breakers Keep Tripping

The fuse box or electrical panel in your home is designed to control the current or electrical flow through your home. Each circuit is controlled by a circuit breaker, this device will trip out if the circuit is overloaded or there is any damage to the wiring preventing the correct flow. When a circuit breaker flips out, check to see how many appliances are on the circuit and to see it any are damaged or hot. Then reset the switch. If it continues to flip out you need to call your friendly electrician GoldCoast.

Breaker will also trip out if the wiring becomes damaged, such as rodents chewing it or other mishaps

3.     If your Wiring is Over 10 Years Old

Old wiring can become dangerous and if your home wiring is over ten years old it is advisable to have your friendly local electrician On the Gold Coast check it for you to ensure it’s safe. Old safety switches and circuit breakers may not trip when needed and fail to protect you or your family. They can allow a person to be electrocuted or cause electrical fires

·         Do You Have Any Two Pin Outlets

Some older homes will still have two pin outlets, these should be replaced and a proper ground or earth wire added by your friendly local electrician on The Gold Coast as they are dangerous.

·         Lights That Flicker or Don’t Work

There are a number of reasons lights don’t work, first check that the bulb is ok.
Then check your electrical panel and the circuit breaker switch. If the light still does not come on or flickers, it means you need to call an electrician on The Gold Coast to check the circuit. Do not attempt to make any repairs yourself because electricity is very dangerous and it is illegal to do any repairs yourself in Australia.

All modern homes are protected by circuit breakers and for wet areas with GFCI or Ground Fault Circuit Interrupt outlets. Whenever you have a situation where you circuit breakers or GFCI outlets keep tripping out you need to call you friendly local electrician on The Gold Coast to have the system checked and repaired.

Comments

Post a Comment

Popular posts from this blog

Tips to protect your workplace from electrical hazards

Electricity is the main force used to power and drive everything is our homes and place of work, but it’s often taken for granted as it can’t be seen and only really noticed when it’s no longer there. The very real and ever present danger of electricity is forgotten until something goes wrong, causing a shock or fire and you need the services of an electrician on Gold Coast . Some important tips to protect your workplace from electrical hazards are: Power cords There’s a wide range of electrical appliances used in the workplace and often, there just isn’t enough power outlets available or near enough, so extension cords and strip connectors are commonly used. It’s important when using these that they are not overloaded and that the circuit they’re connected to is properly earthed and protected by a circuit breaker. Safety switches such as RCDs or residual current devices immediately switch off any electrical supply when they detect electricity is leaking into the ear...
Post a Comment
Read more

Top Tips to check for Bad Electrical Wiring

Every year, hundreds of fires are caused by bad electrical wiring  in Queensland, most of these could have been prevented by calling your friendly electrician on The Gold Coast to check your electrical wiring system. The relatively inexpensive service is one of the cheapest insurance policies you can get. For a few hundred dollars, you can have peace of mind knowing your family and property is safe and secure from the dangers of electrical fires. Although an electrician on Gold Coast needs to do the final check there are some things you can do yourself to check between their inspections such as: ·         Fuse box circuit breakers and safety switches About once a month you should give your safety switches and circuit breakers a visual inspection and if they are equipped with a test button try this to ensure they are working properly. Look for any signs of strain, heat distortion, colouring or an unusual smell, Insects in your fuse box pot...
Post a Comment
Read more

How does a Safety Switch protect against electric shocks?

Safety in the home should be your number one concern by reducing or eliminating any electrical hazard that could threaten your family’s safety or your property is vital. Your friendly local electrician on Gold Coast can inspect your home or business’s wiring and install safety switches where appropriate as it’s a fact, that safety switches save property and lives every day on The Gold coast. Many people are not aware of the role of a safety switch or how they differ from fuses and standard circuit breakers. A safety switch is a type of circuit breaker that is able to detect if any current is leaking from a circuit and almost instantly turn that circuit off to avoid injury or electrocution. Safety Switches Safety switches are primarily designed to protect people from any electrical hazard. They do this by turning off the current or power is a fraction of a second. The easiest way to tell them from ordinary circuit breakers is that they have a test button on them allowing you to r...
Post a Comment
Read more